<label id="aihr5"></label>
    <thead id="aihr5"></thead>

      <thead id="aihr5"><optgroup id="aihr5"></optgroup></thead>
    1. <label id="aihr5"><meter id="aihr5"></meter></label>

        撥號18861759551

        你的位置:首頁 > 技術文章 > 如何測量您的成像系統中的景深

        技術文章

        如何測量您的成像系統中的景深

        技術文章

        Gauging Depth of Field in Your Imaging System

        Over the years, we have answered countless questions regarding lens performance. Of those questions, none have been more difficult to define than requests for depth of field. The reason for this difficulty has more to do with the vagueness of the question than with the inability to provide a measured or calculated value. Consider for a moment what depth of field ls us. It is the distance by which an object may be shifted before an unacceptable blur is produced. For depth of field to be properly stated, it should contain not only the displacement of an image, but also a specific resolution. The depth of field specification is further complicated by a type of keystoning aberration that often occurs. This result can dramatically affect linear measurements and therefore render depth of field unusable. In this article we will take a closer look at depth of field calculations and compare them to physical measurements using the DOF 1-40 depth of field gauge. The gauge, as we will see later, offers a unique look at what depth of field really means and how we as system designers may wish to quantify this parameter. A simple geometric approximation for depth of field is shown in Figure 1.0. The linear blur (required resolution) Bp, Bm and Bf can be expressed in terms of angular blur by the following equation.

        Figure 1

         

        Using similar triangles, a relationship can now be made between angular blur and the focus point,

        where λ is the aperture of the lens. Solving for δplus and δmin,

        The derivation above is very specific to the intended resolution. However, many theoretical derivations of depth of field often assume the lens resolution to be nearly diffraction limited. The most popular of these derivations are based on microscope applications. A typical example for the total depth of field (dplus + dmin) is shown below.

        Where λ is the wavelength and NA equals the numerical aperture of the lens.

        In order to study depth of field we have put together a simple macro system consisting of a 25mm fixed focal length lens, 8mm spacer and Sony XC-75 monochrome CCD video camera. The system was chosen not for its performance but rather for its common real world implementation. Measurements were performed using the DOF 1-40 target. The target allows us to measure depth of field at either 1, 10, 20 or 40 lp/mm over a maximum depth of 50mm. The flat field resolution of this system is approximay 15 lp/mm at 0.3X primary magnification. For purposes of our experiment, a blur spot resolution of 0.1 mm or 10 lp/mm was chosen. Depth of field measurements were taken at three aperture settings corresponding to f/2, f/4, and f/8. An important point should be noted about aperture settings. The f-number shown on most fixed focal length lenses is calculated with the object at infinity. As a result, we have adjusted our NA and therefore our aperture values for a 95mm working distance.

        The values below highlight a number of points to consider. In general our calculated and measured delta d are fairly close. However, the displacement of the image due to defocus aberrations was not predicted by our calculations. This type of displacement error could certainly be problematic if the system contained an auto iris. If we compare our measured results to the delta-theory, we notice a significant variation. As we mentioned earlier, this variation is due to a false assumption concerning system resolution.

        Another property that should be noted in our DOF 1-40 observations is the non-uniform magnification seen through the depth of field range. This is a very common problem in most lenses and, as we stated earlier, can yield significant errors if measurements are made throughout the full depth of field range. Edmund Optics provides several ecentric options to correct for this type of error.

        In the end, it is the total performance of an optical system that counts. As a full service supplier and manufacturer of optics, illumination, CCD cameras, monitors, mounting, and electronic imaging related products, Edmund Optics has the knowledge and resources to look at your application as a total system. In fact, innovative tools such as the DOF 1-40 have come about from our own in-house need to quantify system performance. So if you are looking for individual components that can be integrated into your system or starting from scratch, our engineers are ready to help.

        聯系我們

        地址:江蘇省江陰市人民東路1091號1017室 傳真:0510-68836817 Email:sales@rympo.com
        24小時在線客服,為您服務!

        版權所有 © 2025 江陰韻翔光電技術有限公司 備案號:蘇ICP備16003332號-1 技術支持:化工儀器網 管理登陸 GoogleSitemap

        在線咨詢
        QQ客服
        QQ:17041053
        電話咨詢
        0510-68836815
        關注微信
        主站蜘蛛池模板: 99久久精品国产综合一区| 久久久久一级精品亚洲国产成人综合AV区| 日韩无码系列综合区| 色综合久久久久| 色欲人妻综合AAAAA网| 欧美亚洲另类久久综合| 综合网日日天干夜夜久久| 久久综合一区二区无码| 色欲香天天综合网无码| 五月综合激情网| 伊人色综合一区二区三区| 久久综合狠狠综合久久综合88| 青青草原综合久久大伊人导航| 7国产欧美日韩综合天堂中文久久久久 | 狠狠色噜噜狠狠狠狠色综合久| 综合久久一区二区三区 | 国产激情综合在线观看| 久久精品综合网| 狠狠色丁香婷婷久久综合五月| 久久综合给合久久狠狠狠97色69 | 欧美日韩国产综合视频一区二区三区 | 青青综合在线| 亚洲综合AV在线在线播放| 综合网日日天干夜夜久久| 色天使亚洲综合在线观看| 色欲久久久天天天综合网| 亚洲 欧美 日韩 综合aⅴ视频 | 伊人久久大香线蕉综合5g| 国产精品国产欧美综合一区| 国产精品无码久久综合网| 狠狠色丁香婷婷久久综合| 91久久婷婷国产综合精品青草| 色综合天天综合狠狠| 久久婷婷色综合一区二区| 亚洲精品二区国产综合野狼| 欧美日韩国产色综合一二三四| 狠狠色综合色区| 天天做天天爱天天综合网2021| 高清欧美色欧美综合网站| 久久综合久久综合久久| 国产人成精品综合欧美成人|